N5181A Signal Generators on Sale at BRL Test. Accurate, Pure and Affordable.

N5181A Signal Generators on Sale at BRL Test.
Accurate, pure and affordable.Click for datasheet and quote froms

Call BRL Test Today 407-682-4228

How to Fix Common EMC Problems

Martin Rowe -September 17, 2014

"I keep running into the same EMC problems over and over," EMC Engineer Kenneth Wyatt told an audience of some 40 engineers at a meeting of the Greater Boston IEEE EMC Society. The meeting took place on September 16 at the Bose Corp. headquarters in Framingham, Mass.

"EMC problems appear because many designers don't understand how to design for EMC," said Wyatt. He then spent 90 minutes discussing the causes of EMC problems such as gaps in return planes, cable resonance, shielding, and bonding as well as troubleshooting techniques and tools. Many of the topics Wyatt discussed are covered in The EMC Blog and in his new book EMI Troubleshooting Cookbook for Product Designers: Concepts, Techniques, and Solutions.

Gaps in return planes are one cause of the common-mode currents that produce unwanted emissions. Why? Because current returning to its source has to go around gaps, which lengthens the return path and enlarges the loop that current has to travel. In the video below, Wyatt explains where gaps occur, the emissions problems they cause, and what to do about them.

Wyatt then showed some examples of products that failed compliance tests and why they failed. Take LCD panels, a common problem. There are often gaps between the displays and their enclosures, which can let radiated energy escape. Figure 1, from Wyatt's presentation (download slides) illustrates the problem.

Wyatt explained why LCD displays can be a source of unwanted emissions because LED drivers use LVDS (low voltage differential signaling), which clocks the data at rates approaching 500 MHz and use fast edge speeds. These high frequency, fast edges, tend to couple common-mode currents onto the display cable and housing, which creates emissions that can escape from gaps between the display and enclosure. This is especially true as the length of the gap approaches a half wavelength of a harmonic frequency.

 

Figure 1. Unwanted emissions can escape from around LCD displays.

Poor bonding of cable through enclosures is another problem. Wyatt showed an industrial application where not only wasn't a cable shield connected to a return or reference location, but cables were routed through an enclosure, leaving gaps. Furthermore connectors used for other cables weren't properly connected. That is, connector shells didn't have solid connections to the enclosure. These and other issue can let emissions from clocks and digital circuits out or let outside emissions in.

Wyatt then demonstrated some of the concepts using a Rhode & Schwarz RTE 1104 oscilloscopewith FFT analysis and near-field probes. Figure 2, taken from Gaps in return planes - yes or no?, shows the test setup where he drove two transmission lines—one where the signal traveled over a gap in a return plane and another that didn't— with a digital pulse stream. The harmonics from the emissions were easy to see when the return trace passed over a gap.

Figure 2. A near-field probe and an oscilloscope using an FFT show how a gap in a return plane can create emissions when carrying digital signals.

To close the presentation, Wyatt showed some of the tools and equipment he uses to troubleshoot EMC problems, be they emissions or immunity. His toolbox included

• Loop probes
• Current probes.
• Log-periodic antennas made from PCBs
• RF generators and circuits that generate test signals such as a chattering relay.
• Gaskets, filters, batteries, connectors, and cables
• Several handheld spectrum analyzers. The EMC Blog contains reviews of these and other troubleshooting products.

The evening even had a mini-trade show. Tektronix was there with the MDO4000 and MDO3000mixed-domain oscilloscopes.

Würth Electronik had a table of EMI filters, chokes, ferrites, and connectors. The company held a raffle at the end of the night, giving away two books and a product kit.

4072A Paramteric Testers for less at BRL Test! Expert Configuration and Installation.

We Absolutely know Agilent 4072A Parametric Testers!

Nobody does parametric testers better and cheaper than BRL Test!  Configured your way.  Bam! you're up and running, no problems.  Get everything your company needs and wants without paying the big manufacturer's price tag.  Do you really think some liquidator in Shanghai is going to save you money in the end?  BRL Test is the no worries, big savings, proven alternative to either the manufacturer or the liquidator.

Click here to get a quote now!  Call your BRL Test representative today to get on the right path for your company 866-275-8378.

Q: What's broad, quiet, wide, fast, flexible, easy and stable? - A: Agilent E5071C Network Analyzer!

Q: What's broad, quiet, wide, fast, flexible, easy and stable?
A: Agilent E5071C Network Analyzer!

Need 2 or 4 ports?  No problem.  It can even be configured flexibly up to 22 ports with the E5092A.  High throughput and UI customization are a snap. High temperature stability keeps you in play.  Enjoy clear analysis and easy error correction.  Sounds good?  Call your BRL Test today to see if the E5071C is the right fit for you 866-275-8378.

Click here for low price quotes and data sheet now!